| Processor, Memory, and Operating System |
| Microprocessor | 800 MHz ARM Cortex A8 / NXP |
| Memory Internal Flash | 2 GB NAND and 32 GB extended flash |
| Operating System | Windows Embedded Compact 2013 |
| RAM | 512 MB DDR3 SDRAM |
| Physical |
| Weight | Approximately 2.9 lbs (1330 grams) |
| Display | 5.7 inch (14.5 cm) color VGA resistive touchscreen |
| 640 x 480 pixel |
| Keypad | X button – similar to a Back key |
| 4 arrow buttons to navigate menus |
| Checkmark- similar to an Enter key |
| AC Adapter |
| Battery | Rechargeable Lithium- Ion Power Module |
| Operating Time | 8+ hours of typical use |
| Charge Time | 3 to 4 hours |
| LEDs | 6 LEDs. Five LEDs for indicating the progress of charging. One LED to indicate the AC adapter is charging the power module |
| Battery Charger Options | Input voltage 90-264 VAC, 47-63 Hz |
| Cables included with US, EU, UK, and AU plugs |
| Connections |
| USB | Micro USB Connector. USB 2.0
Remove the USB cable from the Trex unit before connecting to a device. |
| Battery Charger | Barrel Round Plug Tip |
| Wireless |
| Wireless Approvals | FCC, CE, RED and IC Approvals |
| Certified for use in over 100 countries |
| Bluetooth | 2.1 |
| Range up to 10 m |
| Wi-Fi | 802.11 b/g/n |
| Range up to 33 m |
| NFC | Active NFC |
| Range up to 20 mm |
| Communication Modules |
| Device Communicator Communication Module |
| HART terminal | Enables HART device communication |
| Connectors: Two Banana Jack Plugs |
| Optional Internal Resistor: 250 or 500 Ohm |
| Fieldbus (FF) terminal | Enables Foundation Fieldbus device communication |
| Connectors: Two Banana Jack Plugs |
| Device Communicator Plus Communication Module |
| HART terminal | Enables HART device communication |
| Connectors: Two Banana Jack Plugs |
| Optional Internal Resistor: 250 or 500 Ohm |
| HART + pwr terminal | Enables HART communication with the Trex unit, and provides power to one HART device in a bench setup |
| Connectors: Two Banana Jack Plugs |
| Includes HART power supply, resistors (167 Ohm), current control, and ammeter |
| Current Range: 3 -22.5 mA |
| mA terminal (external ammeter) | mA terminal (external ammeter) |
| Connectors: Two Banana Jack Plugs |
| Current Range: Up to 22.5 mA |
| Resolution: 0.1 mA |
| Fieldbus (FF) terminal | Enables Foundation Fieldbus device communication |
| Connectors: Two Banana Jack Plugs |
| FF + FF pwr terminal | Provides power to one Foundation Fieldbus device in a bench setup |
| Connector: One Banana Jack Plug ( Power conditioner included) |
| Current Range: 0- 38 mA |
| Environmental |
| Usage | -20°C to +55°C (-4°F to 131°F) |
| For IS approval: -20°C to +50°C (-4°F to 122°F) |
| Charge | +10°C to +45°C (50°F to 113°F) |
| Storage with power module | -20°C to +50°C (-4°F to 122°F) (less than 1 month) |
| Storage without power module | -20°C to +60°C (-4 °F to 140°F) |
| Enclosure Rating | IP54 |
| Shock | The unit shall survive a 1-meter, all sides and corners drop test onto concrete |
| Upgrade Studio Requirements |
| Installation | Windows 7 Professional Service Pack (SP1) 1 (32 and 64-bit) |
| Windows 10 Professional |
| 512 MB of free disk space |
| A Windows user account with Administrator privileges |
USD
